Search found 120 matches

by petrodood1
Sat Apr 18, 2020 1:44 pm
Forum: Service & Technical
Topic: TLS 350 CSLD 3.0 Gross test fail?
Replies: 5
Views: 343

Re: TLS 350 CSLD 3.0 Gross test fail?

Can you post a picture of the printout from the tls350 ?
by petrodood1
Sat Feb 15, 2020 4:48 pm
Forum: Service & Technical
Topic: Verifone Commander Gift Card Fuel Theft?
Replies: 15
Views: 1207

Re: Verifone Commander Gift Card Fuel Theft?

Had this occur many years ago at a sam's site. Wayne 3v590's with dual cat boards and the POS controller they were using at that time. The customer would swipe a card and the dispenser would authorize, customer would take nozzle out and set the nozzle on the ground and wait for the POS to time out. ...
by petrodood1
Sat Jan 11, 2020 10:07 am
Forum: Service & Technical
Topic: Ovation 3+1 with No plus 1
Replies: 4
Views: 435

Re: Ovation 3+1 with No plus 1

You can flash as 3+0, the only thing I can think of is the ppu boards might have to be changed also, 3+0 used uses 3 ppu board, 3+1 uses 5 ppu board.. And unplug the whip cable on the single grade meter..
by petrodood1
Sun Dec 15, 2019 10:42 pm
Forum: Service & Technical
Topic: Wayne RKI
Replies: 4
Views: 610

Re: Wayne RKI

Uninstall RKI program and reinstall RKI program on my laptop.
by petrodood1
Sat Dec 14, 2019 4:16 pm
Forum: Service & Technical
Topic: Wayne RKI
Replies: 4
Views: 610

Re: Wayne RKI

Never had much trouble with RKI, but the last month or so they had some issues. If you have an RKI that didn't take and won't take after another try you have email RKI support to clear the pinpad S/N out of the server so it will inject. I got a few emails telling me it was either working or not work...
by petrodood1
Sat Dec 14, 2019 4:04 pm
Forum: Service & Technical
Topic: Wayne Dual master SHC
Replies: 4
Views: 381

Re: Wayne Dual master SHC

I was just looking at the manual 920812 Rev. T Wayne Select Install/Operation page 159. In appendix K. it looks like they use a different pulser harness for the twin super high cap. maybe that is the issue (wrong harness).
by petrodood1
Sat Nov 16, 2019 9:01 am
Forum: Construction & Installation
Topic: OPW fill bucket
Replies: 4
Views: 884

Re: OPW fill bucket

Heavy vehicle traffic..
by petrodood1
Sat Oct 26, 2019 2:45 pm
Forum: Service & Technical
Topic: DW 14 Ovation 2 Dispenser
Replies: 4
Views: 625

Re: DW 14 Ovation 2 Dispenser

Make sure you DON'T pick zebra or tearbar when setting up. The pinpad could be the problem also as the printer is fed from the port on the pinpad.. try setting to tearbar and then set back (not tearbar or zebra) and power down the dispenser for a few minutes then power up.. Reload the IX board and t...
by petrodood1
Sun Oct 20, 2019 9:44 am
Forum: Service & Technical
Topic: Ovation alternating sides offline w/commander
Replies: 4
Views: 617

Re: Ovation alternating sides offline w/commander

Sorry for the wrong wording in my post, the site had Gilbarco's prior to getting Wayne Ovation2's, when the commander was reprogrammed the "primary graphics side" was still set on one side of one dispenser, I don't remember the details though...but it did not alternate sides offline..
by petrodood1
Sun Oct 13, 2019 9:52 am
Forum: Service & Technical
Topic: Ovation alternating sides offline w/commander
Replies: 4
Views: 617

Re: Ovation alternating sides offline w/commander

Check the "primary graphic side" side in dcr settings, should be none, I believe.. Had a site w/new Ovation2's from Gilbarco and one dispenser side was set wrong.. and the side would work for short time and then go to E01 message..